....for
all your dock hardware needs in construction of floating docks, swim
platforms, ramps or for other unique applications.
CLICK THIS LINK TO VIEW
DOCK SPECS
Click on a dock hardware item on the
diagram to view description
Dock Hardware Is designed
for use with 1-1/2" thick lumber (minimum width 6"). In general,
inside hardware
can be mounted with 5/16" lag screws or 1/2" carriage bolts. It is
recommended to use 1/2" bolts or screws for all connecting outside hardware. Both male and
female dock to dock connections are made with either 3/4" bolts with lock
nuts or 3/4" connecting pins.
All pricing for hardware
listed is for a commercial grade hardware.
Consumer Tips: To build
a floating dock, we typically use 5/16" x 1 1/2" SS lag screw sets to secure
floats to frame. Angles and inside corners are essential in
constructing your floating dock. Other hardware items depend on your
individual need and connection method. (For more details, give us a call @
1-888-219-0112)
|
Dock Hardware: Outside Corner (Male)
One 1/2" welded tab. Use with a female outside corner to connect docks end
to end. Joint requires 3/4" bolt set (N) or connector pin (O). Each leg is
10"L x 5" H.
|
$25.00 |
 |
(Back to Diagram) |
|
|
Dock Hardware: Outside Corner End
Use this corner at ends of fingers and docks for additional support and
protection. Ideal for swim floats and ski
jump corners. Each leg is 10"L x 5"H.
|
$14.50 |
 |
(Back to Diagram) |
 |
|
Dock Hardware: Inside Corner
This heavy- duty inside corner can be used alone or with an outside
corner. Each leg has elongated holes for easy fit-up and is 8-1/2"L x 5"H.
|
$17.50 |
 |
(Back to Diagram) |
 |
|
Dock Hardware: Inside Corner/Pipe Holder
2"or 3"
These heavy-duty inside corners should be used with one of the outside
corners and as an internal pipe holder to be used with either 2" or 3" pipe or give strength to the dock's frame. Measures 8-1/2"L x 5"H.
Attach using 5/16"x1/12 lag screw sets or carriage bolt sets.
2" Pipe Holder
|
$30.00 |
 |
3" Pipe Holder
|
$35.00 |
 |
(Back to Diagram)
*Special Order |
 |
|
Dock Hardware: Male T Connector
Has one welded 1/2" tab. Use with female T connector to attach fingers and
ramps. 5"L x 5"H. Use 3/4" bolt set or
connecting pin for joint.
|
$13.00 |
 |
(Back to Diagram) |
|
|
|
Dock Hardware: Hinge Set
Hinge Set consists of Male T connector, Female T Connector and
Connector Pin Set. Ideal for
hinging two or more floating docks together.
|
$36.00 |
 |
(Back to Diagram)
|
 |
|
Dock Hardware: Lag Bolt Set
--- 5/16 x 1 1/2" Stainless Steel lag screw and flat washer used to attach flotation drums to
dock system AND for securing inside hardware..
-- 3/8 x 3" Hot dipped galvanized lag screw set work well for mounting
ladders to piers.
---1/2 x 2 or 3" Stainless Steel lag screw and flat washer used for mounting
connecting hardware such as hoops, roller assembly, and hinge sets OR
Carriage Bolt sets can be used as well.
|
5/16" x
1 1/2" SS Lag Screw Set |
$0.75 |
 |
|
3/8" x 3"
Galvanized Lag Screw Set |
$0.95 |
 |
|
1/2" x 2" SS Lag Screw Set |
$2.19 |
|
1/2" x 3" SS
Lag Screw Set |
$2.49 |
 |
(Back to Diagram) |
 |
Dock Hardware: 3/4" Hex Head Bolt Set
Includes lock nut. Used to connect male and female T connectors in the same
manner the connector pin set is used (at the joint). (not for mounting)
Galvanized.
3/4" x 3-1/2".
|
$3.50 |
 |
(Back to Diagram) |
 |
Dock Hardware: Connector Pin Set
For quick disconnect. Used to connect male and female T connectors.
Galvanized 3/4" connector pin and hitch clip pin.
|
$8.00 |
 |
(Back to Diagram)
|
|
Dock Hardware: Heavy Duty Deck Plate
For use with Piling Hoop. This 3/16" thick 4"x6" angle can be bolted from
the top and side of the dock. The hoop can then be bolted to the angle,
allowing it to be removed seasonally. 22" long. Commercial grade.
|
$50.00 |
 |
(Back to Diagram)
|
 |
Dock Hardware: Chain Retainer
Bolts to side of dock. Use weights and chains to hold dock in place.
Accommodates 1/4", 3/8", & 1/2" chain. Measures 5"L x 5"H.
|
$23.00 |
 |
(Back to Diagram)
*Special Order |
 |
|
|
Dock Hardware:
HD Piling Hoops
Made with heavier 1/4" thick hot dip galvanized steel. Commercial Grade.
(Use 1/2" x 3" lag screws or carriage bolts for mounting)
|
8" Diameter (for
6" Piling) |
|
$18.00 |
 |
10" Diameter (for 8" Piling) |
|
$22.00 |
 |
12" Diameter (for 10" Piling) |
|
$25.00 |
 |
14" Diameter ( for 12" Piling) |
|
$35.00 |
 |
(Back to Diagram)
*14" piling hoop- special order. |
 |
|
|
Dock Hardware:
HD Tubular
Piling Hoop
For pilings up to 12" in diameter. The hoop is
constructed of 1 1/2" pipe and is hot dip galvanized. It can be bolted
directly to the side of the dock or to the optional Deck Plate. Commercial
Grade.
|
$70.00 |
 |
(Back to Diagram)
*Special Order |
 |
|
Dock Hardware:
HD Piling Hoop and
Roller Assembly
Intended for areas with lots of wind, current, or tidal action.
Combines the Piling Hoop and Roller Assembly to make up and down
movement easier. For pilings up to 12" in diameter. Commercial
Grade
| $139.00 |
 |
(Back to Diagram)
*Special Order |
 |
|
|
Dock HardwareChain Pile Holder
Made with heavier 1/4" thick hot dipped galvanized steel.
HD galvanized deck
plate with chain for connecting to pilings or pipes. Chain - easy
disconnect. Commercial Grade.
|
$75.00 |
 |
(Back to Diagram)
|
*Note: Center
bumper is made of galvanized steel - it is not a roller. |
|
|
Dock Hardware: Heavy Duty Roller Assembly
Bracket and roller bolt directly to the Deck Plate (not pictured) and can be
added to aid up-and-down motion of the dock in areas with tidal action. 6"
roller turns on a 5/8" diameter shaft. 3/8" bracket is hot-dipped
galvanized. Note: This roller assembly will not work with the pile
chain holder deck plate.
|
$50.00 |
 |
(Back to Diagram) |
|
|
Dock Hardware: Inside Ramp Bracket with Roller
Made of heavier 1/4" hot dipped galvanized steel. Functions as
inside corner for ramp with built-in roller. Left-hand and Right-hand
ramp roller brackets available.
| Left Hand
Ramp Roller |
| $55.00 |
 |
| |
|
Right Hand Ramp Roller Bracket |
| $55.00 |
 |
(Back to Diagram)
|
 |
|
Dock Hardware: Galvanized Eye Bolt
1/2" x 3 1/4" hot dipped galvanized. Includes nut.
|
$4.95 |
|
(Back to Diagram)
|
 |
|
|
Bracket w/roller Assembly |
|
|
